Sludge diaphragm filter press
Sludge diaphragm filter pressThe structure of the combined plate consists of a centre plate and two filter frames, each with a rubber diaphragm in the middle, connected by a dovetail groove. It is very convenient to disassemble and replace the parts. The filter plate is made of modified reinforced polypropylene, and the diaphragm is made of natural rubber or polypropylene, which has high strength, long service life, resistance to acid, alkali and salt, and stable chemical performance. The filter plate adopts medium feeding, uniform feeding, large effective filtration area, clear filtrate, fast filtration speed, shorten the production cycle, increase the number of filtration times and improve the output. Uneven design of the edge of the inner chamber of the filter plate, the edge of the inner chamber of the filter plate has a certain slope, which not only disperses the gravitational force, increases the strength, the filter plate will not be deformed, and the filter cloth will not escape from the slurry due to the large difference between the edge of the inner chamber of the filter plate and the support cam in the middle which causes pulling apart of the warp and weft threads, and the filter cloth is tightly adhered to the slope surface to prolong the service life by more than double.
In contrast to chamber filter plates and filter plates and frames, diaphragm filter plates have a backward and forward movable filter surface - the diaphragm. When a pressing medium (e.g. compressed air or water) is passed through the back side of the diaphragm, these movable diaphragms bulge out in the direction of the filter chamber, so that the filter cake in the chamber is uniformly pressed on the entire filter surface, i.e. it is squeezed again after the filtration process is over.
Sludge diaphragm filter press working principle
sludgediaphragm filter pressThis is a filter press consisting of a set of diaphragm plates and side plates. On both sides of the diaphragm plate, there is a rubber diaphragm, and the outside of the diaphragm is covered with filter cloth, and the side plate is an ordinary filter plate. Material can be added to the chambers through the feed holes in the thrust plate. If solid particles are found to be larger than the aperture of the filter medium (filter cloth), they are intercepted in the chambers, and the filtrate flows out of the outlet holes under the filter plates. If the filter cake needs to be squeezed dry, in addition to the diaphragm press, can also be compressed air or steam, from the washing port into the airflow to wash away the water in the cake, in order to reduce the water content of the cake.
Advantages of sludge diaphragm filter press
For production processes where the filter cake has to be washed sufficiently, diaphragmfilter pressThere are other advantages of the technology. In the process of filter cake washing, the cake is always under pressure in the filter chamber, then after the cake shrinks and thins, the diaphragm protrudes outward to fill in, so that the cake is in a state of compaction, so as to avoid cracks in the cake during washing. At the end of the washing process, the filter cake is pressed to improve the final solids content of the cake. In the case of chamber filter presses, the solids content can only be increased by blowing air into the cake for a prolonged period of time.
For some minerals, such as metal hydroxides and chlorides, an increase in the solids content of the filter cake of even 11 TP3T is important for the overall production process. It is well known that the full utilisation of mechanical dewatering is particularly important as the cost of heating and drying is approximately ten times that of mechanical dewatering. Based on this we have developed a high pressure diaphragm filter plate with a post press pressure of 25 atmospheres and have successfully solved the key technical problems at the feed and at the folding of the diaphragm edges. Its significant advantages are: under the conditions of saving investment, increasing processing capacity and reducing operating costs, the solid content of the filter cake can be accurately adjusted according to the requirements.
Sludge diaphragm filter press industry applications
1、Chemical industry: dyestuffs, pigments, caustic soda, chlorine muted monitor mud, silica, saponin, graphite, bleaching powder, Lide powder, phosphor, insurance powder, chloric acid powder, copper sulphate, manganese sulphate, ferrous sulphate, ferric hydroxide, water purifying agent (aluminium sulphate, polymerized aluminium chloride, alkaline aluminium chloride) and so on.
2. Pharmaceuticals: antibiotics (aureomycin, erythromycin, spiramycin, wellbutrin, madicin, tetracycline, safranin, hygromycin), calcium phytate, traditional Chinese medicines, myo-inositol, growth derivatives of yarns, organophosphorus, saccharomyces cerevisiae and so on.
3、Foodstuffs: yellow wine, white wine, fruit juice, beverage, beer, yeast, citric acid, vegetable protein, vegetable molassesin, glucose, maltose, starch sugar, starch, rice flour, corn syrup, gum, carrageenan, monosodium glutamate (MSG), spices, sauce liquid, oral liquid, soya milk and seaweed, anaconda tablets, benadryl tablet and so on.
4、Metallurgy: gold ore, silver ore, copper ore, iron ore, zinc ore, rare earth and other powder beneficiation.
5、Oil refining: white oil, fragrance oil, light oil, glycerin, mechanical oil, vegetable oil, etc.
6, clay: kaolin, bentonite, activated clay, porcelain clay, electronic ceramic clay, etc..
7, sewage treatment: chemical sewage, smelting sewage, electroplating sewage, electrolytic sewage, leather sewage, printing and dyeing sewage, brewing sewage, pharmaceutical sewage, environmental sewage, paper sewage.
8、Mine: Coal processing industry, coal processing, tailing coal treatment, coking coal and so on.
Technical parameters
| FBXY 200-560/1500 400-1200/1800 Main performance/technical parameters: |
| Working filtration pressure | 0.4-0.6MPa |
| Maximum filtration pressure | 22MPa |
| Filter plate acid and alkali resistance | 2＜PH＜12 |
| Temperature resistance of filter plate | 0-100°C |
| Cake thickness | 32-35mm |
| valid itinerary | 1200mm |
| Diaphragm Pressure | 8-18MPa (subject to no material spray) |
| Area/Filter Plate | filter plate | capacity | power (output) | weights |
| mm | lump (of earth) | m3 | kw | kg |
| FBXY 200/1500 | 51 | 3.8 | 8 | 24300 |
| FBXY 220/1500 | 55 | 4.1 | 8 | 25660 |
| FBXY 250/1500 | 63 | 4.7 | 8 | 28250 |
| FBXY 280/1500 | 71 | 5.3 | 8 | 30920 |
| FBXY 300/1500 | 75 | 5.7 | 8 | 32100 |
| FBXY 320/1500 | 81 | 6 | 8 | 33950 |
| FBXY 340/1500 | 87 | 6.4 | 8 | 35860 |
| FBXY 400/1500 | 101 | 7.6 | 8 | 40400 |
| FBXY450/1500 | 115 | 8.5 | 8 | 45000 |
| FBXY500/1500 | 127 | 9.5 | 8 | 48860 |
| FBXY560/1500 | 143 | 10.6 | 8 | 54100 |
| FBXY 400/1800 | 69 | 7.6 | 8 | 47600 |
| FBXY 450/1800 | 77 | 8.5 | 8 | 51900 |
| FBXY 500/1800 | 87 | 9.5 | 8 | 57000 |
| FBXY 560/1800 | 97 | 10.6 | 8 | 62300 |
| FBXY 600/1800 | 103 | 11.4 | 8 | 64790 |
| FBXY 630/1800 | 109 | 11.9 | 8 | 67400 |
| FBXY 700/1800 | 121 | 13.3 | 8 | 73800 |
| FBXY 750/1800 | 129 | 14 | 8 | 77500 |
| FBXY 800/1800 | 139 | 15.2 | 8 | 82500 |
| FBXY 900/1800 | 157 | 17 | 8 | 93700 |
| FBXY 1000/1800 | 175 | 19 | 8 | 96000 |
| FBXY1100/1800 | 191 | 20.9 | 8 | 105800 |
| FBXY1200/1800 | 209 | 22.8 | 8 | 118600 |
| Remarks: | The final explanation of this product belongs to su-ton and is subject to change without prior notice.
|
| Sales Calls: | TEL:18118100011 |
To learn more about our products, please contact our engineers: 188-517-18-517 for your customised solutions.
Contact Us
Sales:181-181-000-11
Selection:188-517-18-517
Mailbox:suton@su-ton.com
What are your main products?
Various industrial filter presses include manual, mechanical, hydraulic, programme-controlled automatic, high-pressure diaphragm, automatic flushing, automatic plate vibration and other series, plate and frame filter presses, chamber filter presses, vertical filter presses, belt filter presses and stacked-screw filter presses of more than 200 models.
What are the applications of your products?
Municipal sewage, industrial wastewater, chlor-alkali chemical industry, metallurgy, printing and dyeing, ceramics, food, medicine, iron and steel, mining, petroleum and coal, fine chemical industry, environmental protection and other industries waste liquid treatment, solid-liquid separation and recycling of raw materials in the production process, solid-liquid separation in a number of fields in the leading position.
Can you guys help me choose a model?
Of course! Our engineers need the temperature and viscosity of the material in the state of filtration, physical and chemical properties, processing capacity per unit of time, moisture content of the cake, solid content in the filtrate and so on. Selection of the model according to the placement space. The choice of model size (filter area and chamber volume) is mainly determined by analogy and laboratory tests.
Why is it so slow to quote a price?
Because the filter press belongs to non-standard customisation, there are many models, and the price range is also very large. Even if the same model, the material used and the configuration is not the same, the price difference is also very large, to the most common filter press control parts - PLC, for example, the price of a first-line brand PLC is several times the price of ordinary PLC. Therefore, we need to determine the relevant information, and ultimately give you an accurate price. Under normal circumstances, if you provide more comprehensive information, you can quote within 15 minutes.
What information should I provide when I need a quote?
Normally, if you want to get an accurate quotation, you are recommended to provide us with this information: 1. The type of sludge to be filtered: is it physical sludge, or biochemical sludge? Conventional filter presses are available for physical sludge, while belt and stacked-screw filter presses are required for biochemical sludge, especially sludge containing oil or viscous sludge.?
2, the water content of sludge after filtering: chamber filter press, plate and frame filter press, diaphragm filter press after filtering sludge with low water content, stacked-screw filter press after filtering sludge with slightly higher water content, belt filter press with the highest.?
3, sludge treatment of continuous or intermittent: chamber filter press, plate and frame filter press, diaphragm filter press filter press can only be used in an intermittent way to deal with sludge, belt filter press and stacked-screw filter press can be a continuous treatment of sludge, high processing efficiency.?
4, sludge treatment to meet the floor space requirements: If the customer has a floor space limit, then you can choose vertical filter press, but it will cause the increase of this, if there is no floor space limit, then you can choose other ways.
5, the different forms of filter presses on the feed pump requirements: chamber filter press, plate and frame filter press, diaphragm filter press filtration mode because of the use of intermittent, it is recommended to use diaphragm sludge pumps, while if the belt filter press and stacked screw filter press is recommended to use the sludge screw pumps, you can also use diaphragm sludge pumps.
6, the choice of filter cloth: filter cloth to be selected according to the type of sludge, the regular situation according to our selection book, special circumstances to be selected after a small pilot device test.?
7. Site installation conditions (horizontal or vertical installation) and other information.
It's okay if you don't know much about it, our sales managers will assist you in determining that.
Do you have any of your filter presses in stock?
Filter press models and configurations are particularly many, belonging to customised products, we need to select the filter press according to the data you provide to filter the area of the filter, the volume of the chamber, the inlet and outlet of the liquid, the PH value and installation conditions and other working conditions for the selection of filter presses, and to determine the model of the filter press and the configuration of the filter press before delivery to the workshop to place an order for production.
What is your typical lead time?
Depending on the size of the filter press and the specifics of the project, lead times are typically between 30-45 days.
Filter press selection must know:
1. What is the total amount processed in a day (24 hours)?
2. How many hours of work are required in a day (24 hours)?
3. What is the solids content of the sludge sludge at the feed port?
4. The nature of the material (e.g. sludge, calcium carbide sludge, etc.)? Is it organic, biochemical, etc.?
Please contact our sales team for details.
Plate and frame chamber diaphragm filter presses
EN 
ZH_CN 